Swimming Pool Heat Pump System

Swimming Pool Heat Pump System | Geson Chiller

Introduction

If you want to keep your pool nice and warm all season long, then you should get a swimming pool heat pump from Geson.

Geson has been a trusted name in the global heating and cooling market for many years now.

Our swimming pool heat pumps are among the best in the global market.

What is a Swimming Pool Heat Pump?

A swimming pool heat pump is a device that uses electricity not to generate heat but to draw in heat from the warm air outside.

It’s a type of pool pump that circulates the water in the pool, allowing it to pass through the filter, pool pump, and heater.

It makes pools warm and cozy for a pleasurable swim anytime in warm climate.

Swimming Pool Heat Pump

How Does A Pool Heat Pump Work ?

Heat pumps have fans that draw heat from warm air, then circulates it through the outer air coil of the corrosion resistant evaporator fin.

The corrosion resistant evaporator fin absorbs the heat, converts it into gas, pumps it toward the compressor to make the gas pool heaters, and then pushes it through the condenser.

Swimming Pool Chiller

The pump will then circulate the water and push it towards the filter and the heater to further increase its desired temperature.

The hot gas then passes into the condenser where it turns into liquid again so that the evaporator can use it to restart the process.

Figure 1. Swimming Pool Heat Pump Diagram

How are Swimming Pool Heat Pumps Installing?

If not a heat pump pool heaters, then pool owners other option is most likely a gas pool heaters.

While a swimming pool chiller may seem to cost higher than the gas pool heater, the former boasts of lower operating costs because their energy efficiency rating is way better.

Swimming Pool Heat Pump Installation

Properly maintained heat pump pool heaters also last longer.

It means that installing a heat pump pool heaters will provide higher long-term savings.

Constant Temperature Swimming Pool Heat Pump

What Size of a pool heater Should You Get?

The capacity of the pool heater will depend on the size of the pool.

Experts advise using a heat pump pool heaters with an output of 50,000 BTU for every 10,000 gallons of pool water.

For example, you should get a 110,000 BTU heat pump for your 20,000-gallon pool water.

Above Ground Pools Heat Pump

How Long Does the Average Swimming pool heater Last?

A well-maintained pool heater can last anywhere from 10 to 20 years.

However, the average life span of a pool heater is 15 years.

Be sure to get the pump from a trusted manufacturer that offers a limited warranty on the device and schedule it for regular maintenance checks.

Pool Heat Pump For Above Ground Pools

What is the type of pool heater?

Constant temperature swimming pool-as the name implies, the water temperature of the swimming pool is always kept within the most comfortable temperature range for the human body: 26℃-28℃.

The categories of pool heater are as follows:

1. Coal pool heater, oil, natural gas pool heater or electric pool heaters:

This type of method wastes resources more seriously and is not recommended.

2. Solar energy pool heater combined with auxiliary heat source:

Solar heating pools is environmentally friendly and economical, and can be used without affecting the aesthetics of the construction environment.

3.swimming pool heater constant temperature technology:

swimming pool heater constant temperature technology will become the most effective heating and cooling air conditioning technology in the 21st century.

According to heat sources, swimming pool heater are mainly divided into air source swimming pool heater, geothermal heat pumps heat pump, and hydrothermal heat pump.

Current pool heater generally uses air energy heat pump heating.

The principle is based on the principle of reverse Carnot cycle,

Use a small amount of electric energy efficiency to drive the compressor to operate,

The high-pressure liquid working fluid passes through the expansion valve and then evaporates into a gaseous state in the evaporator.

And a large amount of gaseous working fluid that absorbs the heat in the air is compressed into a high temperature state by the compressor,

The state of high pressure, and then enter the condenser to release heat to heat the pool heater,

Such continuous heating cycle can heating pools heater to 50°C—65°C,

A portion of calories was consumed during operation,

At the same time, four parts of the energy are absorbed and transferred from the ambient air to the pool heate,

Relatively speaking, it saves three-quarters of energy efficiency.

The price of the constant desired temperature swimming pool in the design and construction is relatively higher than that of the traditional swimming pool.

However, because of the comfortable water temperature and constant water temperature in all seasons, indoor heated swimming pools,

Therefore, it is widely used in swimming pool construction projects such as villa swimming pool construction, fitness club swimming pool construction, resort swimming pool construction, children’s swimming pool construction and other swimming pool construction projects, and it is also deeply loved by operating investors!

The major difference is that an electric pool heater is powered by electricity while a natural gas pool heater is fueled by natural gas.

Pool owners and pool enthusiasts often wonder what type of pool heater to buy for their pools. There are three types of pool heaters: electric, natural gas and heat pump.

Heat pump pool heater works like an air conditioner in reverse. It uses electricity to pull the heat out of the environment and put it into the water through a process known as ‘refrigeration’. The electric power can be provided by solar panels or wind turbines.

Electric pool heaters work with electricity and operate independently from your home’s power supply. They can’t provide as much heating as a natural gas or a heat pump, but they’re cheaper and easier to maintain.

Natural gas fired boilers use natural gas from your home’s natural gas supply to provide heating for your swimming pools. Natural gas or propane is much more efficient than electric heating for pools in warmer climates. The cost of natural gas or propane combined with increased efficiency can make natural gas a much more economical choice for pools in warm climates than electric heating.

Can You Add a Swimming Pool Heat Pump to an Existing Pool?

You can add an Air Source heat pump pool heaters create to an existing pool water, including the ones that may already have a natural gas pool heater installed.

Swimming Pool Heat Pump can work alongside natural gas pool heater to heat the water rapidly, which is helpful during the colder days.

Contact an expert Swimming Pool Heat Pump installer to help you with the setup.

Air Source Swimming Pool Heat Pump

Where Should You Install An Air Source Heat Pump For Swimming Pool?

Install a heat pump pool heaters create on a flat surface above or below the water level, depending on its configuration.

For best results, install it on a wood or concrete base.

If you have sand around your pool, try to install the heat pump on top of paving slabs.

Figure 2. Outdoor swimming pool heat pump

Can You Install an Air Source Swimming Pool Heat Pump with Chiller Yourself?

It is best to hire a heat pump pool heaters expert or at least a licensed electrician for installation purposes.

While it’s possible for anyone with basic handyman skills to install the heat pump, working with professionals is best because they would know where its most suitable location will be.

They will also check the minimum clearance, water flow rate, plumbing, and electrical supply requirements of the heat pump.

Above Ground Swimming Pool Heat Pump

What are the Disadvantages of Installing a Swimming Pool Heat Pump And Filter?

There aren’t a lot of disadvantages when pool owners installing a Swimming Pool Heat Pump aside from high upfront Swimming Pool Heat Pump Installation Cost and difficult installation.

Swimming Pool filter

But while installing a heat pump for your pool, pool owners may cost a lot at the onset, its long-term operating cost is lower.

If you have issues with installation, simply call an expert heat pump technician.

Pool Heater

Our Swimming Pool Heat Pumps Expensive?

The swimming pool heat pump price may vary greatly depending on Pool Heat Pump Sizing.

These devices are not very expensive, although you may find other options that are cheaper than them, especially when all costs are considered.

Decide wisely when choosing which heating device to use for your swimming pool because your choice may greatly affect the results and your experience.

Do Swimming Pool Heat Pumps Use a Lot of Electricity?

A conventional Air Source swimming pool heat pump heats water by up to a quarter of a degree per hour.

To heat a liter of water by one degree, a Best Swimming Pool Heat Pump normally consume 1.16 watts.

If your pool is 10 cubic meters in size, then your heat pump will spend around 11.6 kW of power heat your pool.

Why is the Electric Bill Get So High with a Swimming Pool Heat Pump?

Technically speaking, your electricity bill will increase by 17% when you use a swimming pool heat pump on a regular basis.

Total energy efficient consumption will always depend on how frequently you need to heat your pool.

Your bill will naturally be lower during the summer and higher during the cooler seasons.

How Much Does It Cost to Run a Swimming Pool Heat Pump?

If you decide to heat your pool, there will always be operating costs to consider regardless of what device you are using.

swimming pool heat pump cost may increase your energy efficient consumption, but it won’t be as high as your other options.

swimming pool heat pump are very efficient devices, which is why they are highly preferred by a lot of people.

What is the Most Efficient Way to Run a Swimming Pool Heat Pump?

To efficiently run your swimming pool heat pump Calculator, you can start by covering up your pool to reach the required temperature faster and maintain the heat.

Be sure to keep the vents, coils, filters, and baskets clean at all times.

Using other devices along with the heat pump, such as solar heaters and automatic timers, may also help greatly.

Swimming Pool Heat Pump Calculator

How Long Does It Take for a Heat Pump to Heat a Pool?

On average, swimming pool heat pump would require one to three days to heat your pool.

This will depend on a lot of other factors as well, such as the current season and the size of your swimming pool.

In case you are using the heat pump for a spa, it will only take an hour or so.

By How Much Can a Swimming Pool Heat Pump Raise the Water’s Temperature?

Generally, you can get your swimming pool heated at around 30 degrees Celsius or 88 degrees Fahrenheit.

However, there are some brands that can go up to 32 degrees Celsius.

The limit of most heat pumps is set at 40 degrees Celsius or 100 degrees Fahrenheit for the user’s safety.

At What Temperature Do swimming pool heat pump Become Ineffective?

For a swimming pool heat pump to work efficiently, the external temperature should be no lower than 15 degrees Celsius or 60 degrees Fahrenheit.

Some heat pumps may still work at 10 degrees Celsius or 50 degrees Fahrenheit.

However, some of them may shut off when they go lower than 7 degrees Celsius or 45 degrees Fahrenheit.

How Often Should You Run a Swimming Pool Heat Pump?

Use the heat pump according to your needs and temperature requirements.

During the summer, try not to use the heat pump at all to save on energy costs.

However, during spring and fall, it is okay to have it running for a few hours to a couple of days as needed.

What is the Best Pool Heater for You?

There are many different types of heat pump pool heaters available these days, which can make it difficult for prospective buyers to figure out what the best choice is.

Here are some of the most common types of heaters available for purchase, along with their pros and cons.

Gas heaters are great for pools that have a lot of water volume. They also work well in colder climates because they do not need power to operate properly. On the flip side, gas heaters do not work as well in warm and mild weather because they produce excess humidity that must be vented with an exhaust system.

Electric heaters are popular because they are easy to install and use less energy than gas models. They also tend to last longer with heavy use than gas models will, but electric models can interfere with

The first thing is what type of fuel source do you want the heater to use? There are three types of fuel sources: electric pool heaters, gas and heat pumps. All three have their advantages and disadvantages.

Gas heaters burn natural gas so they don’t release any fumes or chemicals into the air, but they also cost more to install and buy than electric pool heater or heat pump models do. Heat pumps work by running water over an electric pool heater coil and then emitting it back into the pool as warm water which heats up the pool very quickly.

Propane pool heaters are a good option for those who want to use natural gas as their heating fuel.

The first thing you need to do is find out if your neighborhood has natural gas lines. If so, you will have the option of installing a propane heater or tankless water heater as your heating system.

A propane heater will cost less upfront because it doesn’t require a new natural gas line installation and furnace replacement.

A heat pump pool heater is a very reliable heating solution.

You can install these heat pump pool heaters indoors, and also outside. They work by using a compressor and a gas engine to produce heat. It has an output of 50000 BTU at maximum capacity, which is enough to keep your pool warm even when the temperature drops below 55 degrees Fahrenheit.

The most important thing about this is that it’s reliable heating solution for your pool.

Can a Swimming Pool Heat Pump Run at Night?

Since a heat pump draws heat from ambient air, it works best when used during the day when the sun is out.

However, if you need to use the pool early in the morning, then it’s okay to have it running all night.

The function of the heat pump doesn’t rely on the sun, but the temperature of the ambient air circulating around it.

Can You Leave a Swimming Pool Heat Pump on All Day?

Yes, it is okay to have your swimming pool heat pump running all day.

After all, these devices are highly efficient and tough.

Many people run their heat pumps for at least 12 hours a day.

Is It Bad to Run a Swimming Pool Heat Pump for 24 Hours a Day?

It’s not bad to run a swimming pool heat pump for 24 hours each day.

In fact, many people have kept it running for a maximum of three days without any issues. Check the manual to be sure.

However, some people think about the costs, which is why they reduce the hours of operation.

Are swimming pool heat pump Noisy?

A good swimming pool heat pump will not make a lot of noise.

The typical level noise that heat pumps produce is around 55 to 70 decibels.

The really good ones can go even lower than that.

How Do You Stop a Swimming Pool Heat Pump from Making Noise?

If your swimming pool heat pump is making a lot of noise, then it may need maintenance.

You could also place rubber pads under the device to minimize the noise.

Other times, the piping that’s strapped tightly to the refrigerant causes the noise.

Contact a technician to have it checked.

Will a Swimming Pool Heat Pump Work in the Winter?

Since a swimming pool heat pump draws heat from warm air, it will be challenging to use it during the winter warm climate.

However, you may still use heat pumps in winter provided that the temperature outside is higher than 10 degrees Celsius or 50 degrees Fahrenheit.

Some may even work a couple of degrees lower.

Should the swimming pool heat pump be Turned Off in the Extreme Cold?

It’s highly recommended that you do not use the Above Ground Pools Heat Pump when it’s extremely cold outside.

When the air is icy cold, the heat pump will struggle to achieve the desired temperature.

It’s best that you winterize the heat pump during the harsh winter season.

How Do You Make a swimming pool heat pump More Efficient in the Winter?

If you really need to use the Above Ground Pools Heat Pump during winter, it’s best to use it along with other heating devices, like a solar heater.

Using a solar cover for your pool will also help.

Make sure that you give your heat pump a professional maintenance check before the winter season comes around.

Does a swimming pool heat pump Need to be in the Sun?

It isn’t necessary to install swimming pool heat pump under the direct sunlight.

It only needs ambient outdoor temperature to work efficiently.

When installing a heat pump, make sure that there’s a 50 cm clearance around it.

Can a swimming pool heat pump Cool a Pool?

There are heat pumps that can work in reverse mode, which cools the pool instead of warming it up.

To cool a pool, you’ll need to activate the heat pump’s reverse-cycle.

Check the manual of your device to know if it comes with this feature.

What is the Best Swimming Pool Heat Pump?

There are many swimming pool heat pump available in the market today, and one of the best ones is Geson.

Geson is a global player in the heating and cooling industry.

Based in Nanjing, China, Geson has many years of experience in the field.

How Do I Choose a Swimming Pool Heat Pump?

Consult with an expert manufacturer of the device like Geson.

Give them all the details of your pool along with your requirements.

Our technicians will give you good recommendations on what kind of heat pump you need.

Choose from our wide collection of high-quality heating and cooling products.

How Can I Buy a swimming pool heat pump?

If you need swimming pool heat pump Prices, contact us here at Geson, swimming pool heat pump For Sale.

You can also see swimming pool heat pump Reviews on our website.

swimming pool heat pump Prices South Africa, swimming pool heat pump Nz, all can consult our engineer for the market.

We’ll assist you in every step of the purchase.

We guarantee you that all our products passed strict standards of quality control for your peace of mind.

What Pool type?

Generally, swimming pools are divided into the following pool type according to different purposes:

above ground pools

inground pools

1. Competition swimming pool, it is larger swimming pools.

2. Public swimming pool

3. Dedicated swimming pool

4. Private swimming pool

5. Leisure play pool

6. Chute drop pool

7. Wave pool

8. Jacuzzi

9. Paddling pool

10. Foot bath

Why do swimming pool heater use titanium heat exchanger?

The heat exchanger of the swimming pool heater is titanium heat exchanger, the inner material is pure titanium, and the outer surface is a high-strength PVC tube. “

“Titanium” is an aerospace material with corrosion resistance and good thermal conductivity.

The heat exchanger of the pool heater is red copper, which is not corrosion resistant and cannot be in direct contact with swimming pool water. It is not a special swimming pool titanium heat exchanger.

pool heater need to add water tanks, plate heat exchangers, and pool pumps, so the later operating costs of the swimming pool will be higher.

The use of pool heater for swimming pools cannot achieve precise control of the swimming pool temperature.

Therefore, a dedicated swimming pool heater with titanium heat exchanger should be used to heat the swimming pool to save later operating costs.

How to Selection of heat exchanger for pool heater？

Smaller swimming pools, especially family swimming pools, do not need heat exchangers.

And use heat pump, electric pool heaters or small fuel gas pool heaters (pool temperature, T<55℃),

Direct heating of the circulating pool water,

But it should be noted that when the furnace outlet pool temperature is 40℃<T<55℃,

Effective measures must be taken to ensure the full mixing of heated water and unheated water.

In most other cases, swimming pool water generally uses heat exchangers to indirectly heat the pool water.

What the Working Principle of the swimming pool heater?

The working principle of the swimming pool constant temperature dehumidification pool heater is to recycle the heat loss from the evaporation of the pool water surface and transfer it to the pool water and air.

In order to meet the heat required for the heat preservation of the pool water and air.

First, the warm and humid air flows through the evaporator, thepool temperature drops,

The warm water vapor is condensed into cold water and separated from the air, making the air dry and realizing the dehumidification function of the air;

The heat energy released in the air cooling, water vapor condensation and cooling process is absorbed by the refrigerant.

In the second step, the high-temperature refrigerant absorbs heat energy and heats the pool water through the heat exchanger to achieve the pool water heating function; the other part of the heat passes through the reheater to heat the cooled indoor air to achieve the air heating function.